Your Position: Home > amFilm® Screen Protector  >Screen Protector Installation

S22U-UV

  • Step #1:
    Plug in and turn on the UV light to check if it works properly.
  • Step #2:
    Turn off your device and apply the leveling pads to the back of your phone. Clean the screen with the wet wipes and cleaning cloth.
  • Step #3:
    Use the Screen-Prep cloth to wipe the surface of device screen a few times.Then use the cleaning cloth to clean the screen again. This will heLp to prevent the bubbles during application.
  • Step #4:
    Place the application tray on your phone. Make sure to align the side labelled “top” with the top of the phone. Press firmly into place.Then insert the pins on each end of the application tray.
  • Step #5:
    Make sure the phone is 100% level by using the included bubble level. Set it in the middle of the phone’s screen.The bubbles will be centered when surface is flat.
  • Step #6:
    Place absorption pads in the side slots located on the longer edges of the application tray. Re-clean the screen using dust removal stickers if needed.
  • Step #7:
    Unscrew the RED cap of the first adhesive tube. Hold the tube over the left set of pegs on the application tray with the opened end facing down. Unscrewing the black cap will release the adhesive in the tube.
  • Please drip the adhesive to the inside of right and left peg lines (about 5mm from the peg lines) as shown above
  • Step #8:
    Drip all the adhesive to the left circle as shown above. Repeat step 7 with second adhesive and drop all the adhesive to the right circle as shown above.
  • Step #9:
    Peel off the mask film of the screen protector, and set if within the tray, resting it on the pins on either edge of the phone. Make sure the camera cutout is aligned with the top of the phone, where the device’s front-facing camera is located.
  • Step #10:
    SLOWLY pull both pins outward to allowthe protectorto lower onto the adhesive. Once the protector touches BOTH adhesive puddles, pull the pins out the rest of the way AT THE SAME TIME.
  • Step #11:
    The adhesive will begin spreading on its own.While it is spreading, place the metal cylinder on the fingerprint scanner sticker.
  • Step #12:
    Wait for the adhesive to fully spread to all edges of the phone. DO NOTTOUCH the screen protector during this time.
  • Step #13:
    Plug in the UV Light and prop it up on its legs.Then turn it on.Place the UV Light over the top, middle, and bottom of the tray, and cure for 20 seconds each.
  • Step #14:
    Remove the installation tray (by pushing on the screen protector gently),metal cylinder and scanner sticker.
  • Step #15:
    Use the UV Light again on the top, middle and boffom of the phone for an additional 60 seconds each.
  • Step #16:
    Rescan your fingerprints info the phone system if needed, and enjoy the screen protector!

Best Sellers

  • amPlus Basic Protection Plan ($2.99/M)

    amPlus Basic Protection Plan ($2.99/M)

  • amFilm Galaxy S22 Ultra (6.8” 2022) Ultra Glass Screen Protector (3-Pack)

    Galaxy S22 Ultra UV Glass Screen Protector 3-Pack

  • amFilm OneTouch Screen Protector & Camera Protector for iPhone 13 Pro Max (2-Pack Each)

    iPhone 13 Pro Max OneTouch & Camera Screen Protector Combo 2-Pack

    amFilm OneTouch iPhone 14 & iPhone 13/13 Pro Glass Screen Protector (6.1

    iPhone 13 & 13 Pro OneTouch Glass Screen Protector 2-Pack

    amFilm iPad Mini 6 (2021) Glass Screen Protector 2-Pack

    iPad Mini 6 Glass Screen Protector 2-Pack

    amFilm Nintendo Switch OLED Glass Screen Protector (3-Pack)

    Nintendo Switch OLED OneTouch Glass Screen Protector 3-Pack